Check vavle on domestic side of hot water heater.

We had a boiler guy (not on this forum) out a couple months ago and since then the TP valve has been blowing off pretty regularly. I know very little about water systems but from the research I've been doing I think he caused an issue by installing a check valve about 3' in front of the water heater on the cold water input line from the well. There is no expansion tank on the hot water system.

We plan to have the water heater replaced very soon but I'm wondering if I need to get that check valve out of there ASAP. I don't mind the bit of water from the T&P blowing off but I'm concerned about the safety of the system now that I think I know what the issue is.

You need an expansion tank

Quote:

---

Originally Posted by Wulf202

You need an expansion tank

---

Do we have time to wait until we replace the hot water thank or is this more of an urgent issue? Wouldn't removing this check valve (back to the way it was before) allow some pressure to be pushed back towards the well pressure tank?

Yea most likely. But small expansion tanks like that are really cheap. I feel like I got one at home depot one time I the 20-40$ range, but could be wrong. Just remember the more times a relief valve pops off the greater the chance it won't reset

Quote:

---

Originally Posted by fitterjohn

Yea most likely. But small expansion tanks like that are really cheap. I feel like I got one at home depot one time I the 20-40$ range, but could be wrong. Just remember the more times a relief valve pops off the greater the chance it won't reset

---

My worry is my lack of DIY skills and not the cost (although I don't want to pay the $500+ I'm sure a plumbing company would charge to install an expansion tank on Sunday). I've never soldered a pipe and I'm not sure this is the time to start. :). I'm confident I could cut the check valve out and use compression fittings to get it back to the way it was.

Yea the shark bites aren't too bad, it wouldn't be to hard to get the check valve out, if your confident that's the problem

I had this problem and changed out the water pressure regulator. It fixed it.

https://www.lowes.com/pd/Wilkins-3-4...-Valve/3134067

Quote:

---

Originally Posted by BushMasterBoy

I had this problem and changed out the water pressure regulator. It fixed it.

https://www.lowes.com/pd/Wilkins-3-4...-Valve/3134067

---

I don't have one of those. At the most our pressure hits 60PSI due to the fact that the well pit is about 300' from the house.

Quote:

---

Originally Posted by th3w01f

My worry is my lack of DIY skills and not the cost (although I don't want to pay the $500+ I'm sure a plumbing company would charge to install an expansion tank on Sunday). I've never soldered a pipe and I'm not sure this is the time to start. :). I'm confident I could cut the check valve out and use compression fittings to get it back to the way it was.

---

I put in an expansion tank myself a few years ago . . . it really wasn't too hard and I'm a weekend warrior plumbing noob at best. That was especially true at that time. I just used Shark Bite fittings for that, because it was easy to do and in that application, in a utility room, I can easily monitor and if there is ever a leak I can pop on a new fitting.

Since that time I have tried to learn to solder and am much more comfortable doing that, but I would still probably keep the compression fittings on this if I ever need to work on it. Basically just a "T" off the water line and a coupling for the short pipe to the tank. Then just support it well with some strapping.

Quote:

---

Originally Posted by Ramsker

Basically just a "T" off the water line and a coupling for the short pipe to the tank. Then just support it well with some strapping.

---

Hmmm, a T doesn't sound too bad, I was trying to figure out how to get it fully inline with the short run of pipe that is horizontal.