Building under-the-bed storage.

You can see where the panel cut-out bit just burned the frame:
http://www.johnnyego.com/wood/2017Pr...d/vinbed40.JPG

But most of it is pretty decent, and can be cleaned up with a little effort and some creative routing. This was the most stressful part of the project, and it finished up good enough.
http://www.johnnyego.com/wood/2017Pr...d/vinbed41.JPG

Stout corners:
http://www.johnnyego.com/wood/2017Pr...d/vinbed29.JPG

Day 4

It was ridiculously hot outside, and I only had a few hours to work on things today, so not a ton of progress. Started out trying to salvage something of value out of the panel cut-outs. The track-saw makes getting that first straight cut pretty easy, and from there, the table saw handles making the rest of it parallel and perpendicular.
http://www.johnnyego.com/wood/2017Pr...d/vinbed43.JPG
http://www.johnnyego.com/wood/2017Pr...d/vinbed44.JPG
http://www.johnnyego.com/wood/2017Pr...d/vinbed45.JPG

My goal is to use as much if the plywood as possible. I have a long off-cut that is about 11.5" x 60", and is a fine candidate for the drawer sides. I start by splitting it on the table saw.
http://www.johnnyego.com/wood/2017Pr...d/vinbed46.JPG

Going to route a groove for the floor base with the router table. I set the depth for 3/8", and the width to 1/4" with a set-up bar. If I had to do it all over again, I probably would have set the width to 1/2". I don't think the 1/4 will blow out when assembled into the drawer base, but 1/2 would have been a lot more stout.
http://www.johnnyego.com/wood/2017Pr...d/vinbed48.JPG
http://www.johnnyego.com/wood/2017Pr...d/vinbed49.JPG
http://www.johnnyego.com/wood/2017Pr...d/vinbed50.JPG

A quick check just to make sure.
http://www.johnnyego.com/wood/2017Pr...d/vinbed51.JPG

I was able to use one of the salvaged panels to make some additional sides:
http://www.johnnyego.com/wood/2017Pr...d/vinbed47.JPG

And that was all the time and desire I had to be in the shop today.

Unfortunately, work expected me to actually work for a couple days last week, so I didn't get quite as much accomplished by this point as I had hoped.

Finished working on the center drawers. These are shop-style drawers, built for speed and durability over beauty. Pocket holes facing the front and back, because the front will be covered by the face, and the back won't be easily seen.
http://www.johnnyego.com/wood/2017Pr...d/vinbed54.JPG
http://www.johnnyego.com/wood/2017Pr...d/vinbed58.JPG
http://www.johnnyego.com/wood/2017Pr...d/vinbed59.JPG

Cut some spacers to get the drawers aligned correctly. I have a bunch of unused 28" full extension slides. I needed three pair of them for another project, and it turned out I could get 10 pair online cheaper then buying three individual pairs at Home Depot or Lowes. So they are free, which is good. However, I do not have enough sheet stock to make all the drawers 28", and I do not intend to buy another sheet of ply for this project.
http://www.johnnyego.com/wood/2017Pr...d/vinbed55.JPG
http://www.johnnyego.com/wood/2017Pr...d/vinbed60.JPG
http://www.johnnyego.com/wood/2017Pr...d/vinbed61.JPG

Next day was mostly dedicated to router work. Rounding over all the sharp corners and such.
http://www.johnnyego.com/wood/2017Pr...d/vinbed62.JPG
http://www.johnnyego.com/wood/2017Pr...d/vinbed63.JPG
http://www.johnnyego.com/wood/2017Pr...d/vinbed64.JPG
http://www.johnnyego.com/wood/2017Pr...d/vinbed65.JPG

I did enough sheet waste to build a larger drawer for the right-hand side. One piece of scrap was wider then I could cut with my compound miter, and longer then I wanted to try and cut on my table saw, so I set up my cutting table for cross-cutting. The advantage of this set-up is that I can space the cross members wherever I want them, and have full support for both the panel and the off-cut.
http://www.johnnyego.com/wood/2017Pr...d/vinbed66.JPG
http://www.johnnyego.com/wood/2017Pr...d/vinbed67.JPG

The larger drawer was assembled in the same manner as the smaller one.
http://www.johnnyego.com/wood/2017Pr...d/vinbed72.JPG
http://www.johnnyego.com/wood/2017Pr...d/vinbed73.JPG
http://www.johnnyego.com/wood/2017Pr...d/vinbed74.JPG

Starting to take shape.
http://www.johnnyego.com/wood/2017Pr...d/vinbed75.JPG

Last thing I did was shim the left-side cabinet and trim it out with some dust panels.
http://www.johnnyego.com/wood/2017Pr...d/vinbed69.JPG
http://www.johnnyego.com/wood/2017Pr...d/vinbed70.JPG