Close
Page 1 of 2 12 LastLast
Results 1 to 10 of 20
  1. #1
    My Fancy Title gnihcraes's Avatar
    Join Date
    Apr 2008
    Location
    CastleRock/Lakewood
    Posts
    4,422

    Default LED Strip Lights - Project

    I've been working on some emergency/camping/survival LED lighting. 12 Volt.

    Purchased some LED strip lighting off amazon, 16 foot rolls @ $6.xx bucks per roll. Very rubbery, silicone based covering, flexible, cut to length. 2 Inch minimum, every two inches you can cut.

    Click image for larger version. 

Name:	LED1.jpg 
Views:	106 
Size:	92.8 KB 
ID:	49023

    shortest possible
    Click image for larger version. 

Name:	LED2.jpg 
Views:	111 
Size:	98.7 KB 
ID:	49025

    @ 12 volts

    Click image for larger version. 

Name:	LED3b.jpg 
Views:	109 
Size:	89.3 KB 
ID:	49029
    placed in 3/8 x 3/8 aluminum channel. it's 3M sticky backed, but it doesn't stick well to anything. (probably why it's cheap)
    Click image for larger version. 

Name:	LED4.jpg 
Views:	99 
Size:	116.3 KB 
ID:	49031

    power pole connections and lit up. Strain relief as not to pull apart at the solder traces.
    Click image for larger version. 

Name:	LED5.jpg 
Views:	115 
Size:	239.9 KB 
ID:	49033


    Click image for larger version. 

Name:	LED6.jpg 
Views:	123 
Size:	229.5 KB 
ID:	49035

    Some LED lighting kept us going on a camping trip recently where the deep cycle battery failed during the trip. No amps, limited volts, but ran some LED lighting several hours to play some board games with the kids. Good stuff to have on hand. (built in lights on camper are 1amp each 115x bulbs) LED direct replacement lights are expensive. $20 bulb or so.

    Built all this lighting for about $20 per 16 feet.
    Last edited by gnihcraes; 08-30-2014 at 20:49.
    Sometimes people trip and fall down stairs.
    Sometimes assholes push people down stairs.
    That doesn't mean "stairs are bad" nor does it make someone who pushes someone down the stairs any less of an asshole.

  2. #2
    QUITTER Irving's Avatar
    Join Date
    Nov 2008
    Location
    Denver, CO
    Posts
    46,527
    Blog Entries
    1

    Default

    I used this same LED product to do the lights on my corner pantry. I also bought similar lights from Radio Shack that are brighter, BUT, they aren't constructed nearly as well and are just slid into a bulky rubber sheath. Also, the Radio Shack lights were something like $30 for 6 ft, compared to $6 for 16 ft. The Amazon lights are a MUCH better deal, and easier to work with. You can't just cut the Radio Shack lights without completely ruining the water proofing.

    Gnihcraes, did you drill holes in the aluminum track to run the zip ties through? Great idea by the way.

    In picture #5, you have two zip ties close together at the end of the strip. I might consider tying the wire into a loose knot between those zip ties, so on the off chance that the light is ever dropped or falls, you're not pulling your connections apart. Basically the same thing they do with computer speakers. Great looking project.

    EDIT: My idea for these strips, which I'll never do in the place I live currently, is emergency lighting for the house. One of those 2" strips in each living space in the house would be great emergency lighting for power outages. I think even a small 12v battery like this would probably give you light at night for several days. You could use a portable drill battery as well I bet.
    Last edited by Irving; 08-30-2014 at 21:30.
    "There are no finger prints under water."

  3. #3
    Worlds Shortest Tall Guy kwando's Avatar
    Join Date
    Nov 2005
    Location
    Elizabeth, Colorado
    Posts
    3,675

    Default

    Would make a good light for a press as well to visually check for powder in each load
    "An armed society is a polite society when a man may have to back his last words with gunplay."

    My Feedback

  4. #4
    QUITTER Irving's Avatar
    Join Date
    Nov 2008
    Location
    Denver, CO
    Posts
    46,527
    Blog Entries
    1

    Default

    An 18v drill battery works, but the lights start getting too hot to hold almost immediately. So 18v is a bit too much. Good idea Kwando. Same for over the counter lighting.
    "There are no finger prints under water."

  5. #5
    My Fancy Title gnihcraes's Avatar
    Join Date
    Apr 2008
    Location
    CastleRock/Lakewood
    Posts
    4,422

    Default

    Quote Originally Posted by Irving View Post
    I used this same LED product to do the lights on my corner pantry. I also bought similar lights from Radio Shack that are brighter, BUT, they aren't constructed nearly as well and are just slid into a bulky rubber sheath. Also, the Radio Shack lights were something like $30 for 6 ft, compared to $6 for 16 ft. The Amazon lights are a MUCH better deal, and easier to work with. You can't just cut the Radio Shack lights without completely ruining the water proofing.

    Gnihcraes, did you drill holes in the aluminum track to run the zip ties through? Great idea by the way.

    In picture #5, you have two zip ties close together at the end of the strip. I might consider tying the wire into a loose knot between those zip ties, so on the off chance that the light is ever dropped or falls, you're not pulling your connections apart. Basically the same thing they do with computer speakers. Great looking project.

    EDIT: My idea for these strips, which I'll never do in the place I live currently, is emergency lighting for the house. One of those 2" strips in each living space in the house would be great emergency lighting for power outages. I think even a small 12v battery like this would probably give you light at night for several days. You could use a portable drill battery as well I bet.
    Maybe that is where I got the idea of the LED strips, sorry if I stole it Irving! I remember the radio shack ones, and looked at them, but same thoughts as you, expensive and can't cut it down. $$

    Yes, sticky stuff wasn't working on the aluminum, or anything else really, so I just drilled the holes and zip tied it down every foot. The ends wires are looped back on themselves on one or two, but it seemed to put more pressure on the wires than just zipping them down a couple times.

    My friend has uses similar LED lighting for under counter and cove lighting in his new kitchen, on dimmer switches, so they could also be used as emergency lighting type situations if planned correctly. (cove lighting maybe?)

    The 18ah battery is good, and there are various options out there. I'm going to try and use the 8ah batteries in my portable solar project, more to come on that. We'll have to compare notes Irving, i think you were doing one also.
    Sometimes people trip and fall down stairs.
    Sometimes assholes push people down stairs.
    That doesn't mean "stairs are bad" nor does it make someone who pushes someone down the stairs any less of an asshole.

  6. #6
    My Fancy Title gnihcraes's Avatar
    Join Date
    Apr 2008
    Location
    CastleRock/Lakewood
    Posts
    4,422

    Default

    Quote Originally Posted by kwando View Post
    Would make a good light for a press as well to visually check for powder in each load
    Yep. These do get hotter than you'd think though. Even at 12volts they get pretty warm. Maybe because of the rubber covering/smothering them? I tested and they will run up to 17 volts or more, then they start blinking and shut off due to over volt. They will come back on though, which is a good thing.

    I believe each 4 foot piece is 0.5 amps @ 12 volts. They would run forever on a large sized battery. And, they do run on a 10 - 15 watt solar panel. So in theory, you can run the wires from a solar panel into the house and run the LED's during the day or in a dark basement/room. (panic room?) etc.

    Being LED, they do not Cast like a regular bulb, so lighting a room with them is difficult. (the other one below does a better job)

    Various colors available too I think on amazon.

    The other LED Light that works great is:

    http://www.amazon.com/dp/B008XZAQDU/..._M3T1_ST1_dp_1

    I've got one on the mobility scooter and one for the emergency kit/camper. Worked great with a nearly dead battery in the camper. .4 amps, runs on voltage from 7 beyond 12. I test them on a variable power supply and mark them with the amp rating for future reference in the field.
    Sometimes people trip and fall down stairs.
    Sometimes assholes push people down stairs.
    That doesn't mean "stairs are bad" nor does it make someone who pushes someone down the stairs any less of an asshole.

  7. #7
    QUITTER Irving's Avatar
    Join Date
    Nov 2008
    Location
    Denver, CO
    Posts
    46,527
    Blog Entries
    1

    Default

    Quote Originally Posted by gnihcraes View Post
    The 18ah battery is good, and there are various options out there. I'm going to try and use the 8ah batteries in my portable solar project, more to come on that. We'll have to compare notes Irving, i think you were doing one also.
    Yes we will compare notes, as I'd like to build one as well. Also, of course you never stole any idea from me. Preposterous. Back in my 4 wheeling days, I wanted some rock lights under the truck for night wheeling. I think these would be a perfect, low power option for something like that. Thanks for posting up that LED flood light.
    "There are no finger prints under water."

  8. #8
    Moderator "Doctor" Grey TheGrey's Avatar
    Join Date
    Jan 2013
    Location
    Lone Tree
    Posts
    5,750

    Default

    Great ideas! This is definitely going on The List. Thank you for posting pictures; that helps tremendously!
    "There is nothing in the world so permanent as a temporary emergency." - Robert A Heinlein The Moon is a Harsh Mistress

    Feedback for TheGrey

  9. #9
    QUITTER Irving's Avatar
    Join Date
    Nov 2008
    Location
    Denver, CO
    Posts
    46,527
    Blog Entries
    1

    Default

    Quote Originally Posted by gnihcraes View Post

    The other LED Light that works great is:

    http://www.amazon.com/dp/B008XZAQDU/..._M3T1_ST1_dp_1

    I've got one on the mobility scooter and one for the emergency kit/camper. Worked great with a nearly dead battery in the camper. .4 amps, runs on voltage from 7 beyond 12. I test them on a variable power supply and mark them with the amp rating for future reference in the field.
    I'm going to order one of these to test out. If it works like I want, then I'm going to replace the house mounted lights on either side of my garage with this light mounted in the soffit. I like to have my house lit up, but not have lights glaring every where at the same time. I've grown to dislike bright lights every where when they blind you at the same time. Plus I think it will look nice.
    "There are no finger prints under water."

  10. #10
    Grand Master Know It All Duman's Avatar
    Join Date
    Jul 2014
    Location
    Longmont
    Posts
    2,638

    Default

    I picked up one of these at Costco for ~$30. Just plug it into an inverter connected to the deep-cycle, good to go. I use it for emergencies only, don't know how fast it will drain the battery.

    http://www.amazon.com/Snap-On-Work-L...led+work+light

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •