Close
Page 1 of 2 12 LastLast
Results 1 to 10 of 11
  1. #1
    Grand Master Know It All sellersm's Avatar
    Join Date
    Jun 2011
    Location
    Montrose
    Posts
    4,999

    Default Ball joints replacement 87 S10

    87 Blazer S10 2WD upper & lower ball joints need replacing. My son in law wants to do this job this coming Sunday.

    Any "gotchas" or helpful hints? Anybody done this?

    Thanks!!


    Sent from my fat fingers using Tapatalk
    http://disciplejourney.com

    Make men large and strong and tyranny will bankrupt itself in making shackles for them.” – Rev. Henry Ward Beecher (1813-1887) US Abolitionist Preacher

    CIPCIP

  2. #2
    QUITTER Irving's Avatar
    Join Date
    Nov 2008
    Location
    Denver, CO
    Posts
    46,527
    Blog Entries
    1

    Default

    Youtube, seriously.
    "There are no finger prints under water."

  3. #3
    Does Dishes - In the Buff
    Join Date
    Jun 2013
    Location
    No Co
    Posts
    641

    Default

    Quote Originally Posted by sellersm View Post
    87 Blazer S10 2WD upper & lower ball joints need replacing. My son in law wants to do this job this coming Sunday.

    Any "gotchas" or helpful hints? Anybody done this?

    Thanks!!


    Sent from my fat fingers using Tapatalk
    I've only changed them on a solid axle 4X4 but I'm sure the approach is much the same.

    Start soaking ball joint and tie rod nuts Saturday with penetrating oil like "Blaster" if they're rusty.
    Besides your run of mill tools you'll need a "pickle fork" to remove tie rod ends, a ball joint removal/installation tool, wrench/socket big enough to remove nut on ball joint.
    Plan to replace cotter pins you remove.
    Depending the last time wheel bearing wear replaced you may want to consider replacing them and the races, at a minimum repack them and replace the seals.
    If brakes are getting close to being worn I'd replace them while everything is apart and you may consider turning the disc if they're showing wear or are glazed too.
    Since it's 2wd it should go pretty easy/fast but still plan on spending the majority of the day if it's your first time.

  4. #4
    Grand Master Know It All sellersm's Avatar
    Join Date
    Jun 2011
    Location
    Montrose
    Posts
    4,999

    Default

    Quote Originally Posted by Buff View Post
    I've only changed them on a solid axle 4X4 but I'm sure the approach is much the same.

    Start soaking ball joint and tie rod nuts Saturday with penetrating oil like "Blaster" if they're rusty.
    Besides your run of mill tools you'll need a "pickle fork" to remove tie rod ends, a ball joint removal/installation tool, wrench/socket big enough to remove nut on ball joint.
    Plan to replace cotter pins you remove.
    Depending the last time wheel bearing wear replaced you may want to consider replacing them and the races, at a minimum repack them and replace the seals.
    If brakes are getting close to being worn I'd replace them while everything is apart and you may consider turning the disc if they're showing wear or are glazed too.
    Since it's 2wd it should go pretty easy/fast but still plan on spending the majority of the day if it's your first time.
    Thx!


    Sent from my fat fingers using Tapatalk
    http://disciplejourney.com

    Make men large and strong and tyranny will bankrupt itself in making shackles for them.” – Rev. Henry Ward Beecher (1813-1887) US Abolitionist Preacher

    CIPCIP

  5. #5
    BIG PaPa ray1970's Avatar
    Join Date
    Feb 2010
    Location
    Thornton
    Posts
    18,799
    Blog Entries
    1

    Default

    I recommend some beer and a well balanced vocabulary of curse words.

    Oh, and a big hammer is pretty useful too. Seriously. A 40 oz. cross-peen is my favorite for front end work.

    And please be careful. Those front coil springs have a lot of stored energy.

  6. #6
    The "Godfather" of COAR Great-Kazoo's Avatar
    Join Date
    Sep 2003
    Location
    Washboard Alley, AZ.
    Posts
    48,074

    Default

    Don't forget SAFETY GLASSES. and getting it aligned afterward.

    If you have a compressor and air tools use them.
    The Great Kazoo's Feedback

    "when you're happy you enjoy the melody but, when you're broken you understand the lyrics".

  7. #7
    Machine Gunner Colorado Osprey's Avatar
    Join Date
    Dec 2005
    Location
    Kinda near Peyton, CO
    Posts
    1,388

    Default

    I hope since it is a 1987 that these have been done a few times before since they are notorious for wasting ball joints and idler arms.
    If the uppers are original they are riveted onto the upper control arm. The fastest way to remove the rivets is a torch to heat up the rivet and an air hammer and a chisel bit to shear off the end of the rivet. A drift punch will then drive the rivet out.
    The new ball joints will come with bolts to install.

    Lowers are pretty straight forward.

    Because the ball joints are usually replaced every 30k or so on the S-10/15 series there is also a chance you might need the oversized lower ball joints if the lower control arm is loose where the joint installs.

    Book time if I recall on the 4x4 was close to 2 hrs per side for ball joints. After the 1st 100 trucks they can be done in about 20 min/side. Don't forget to check your idler arm as well, its probably toast.
    I say lets all remove the warning labels and let nature take its course.

  8. #8
    Grand Master Know It All sellersm's Avatar
    Join Date
    Jun 2011
    Location
    Montrose
    Posts
    4,999

    Default

    Quote Originally Posted by Colorado Osprey View Post
    I hope since it is a 1987 that these have been done a few times before since they are notorious for wasting ball joints and idler arms.
    If the uppers are original they are riveted onto the upper control arm. The fastest way to remove the rivets is a torch to heat up the rivet and an air hammer and a chisel bit to shear off the end of the rivet. A drift punch will then drive the rivet out.
    The new ball joints will come with bolts to install.

    Lowers are pretty straight forward.

    Because the ball joints are usually replaced every 30k or so on the S-10/15 series there is also a chance you might need the oversized lower ball joints if the lower control arm is loose where the joint installs.

    Book time if I recall on the 4x4 was close to 2 hrs per side for ball joints. After the 1st 100 trucks they can be done in about 20 min/side. Don't forget to check your idler arm as well, its probably toast.
    Thanks!
    http://disciplejourney.com

    Make men large and strong and tyranny will bankrupt itself in making shackles for them.” – Rev. Henry Ward Beecher (1813-1887) US Abolitionist Preacher

    CIPCIP

  9. #9
    Zombie Slayer
    Join Date
    Sep 2009
    Location
    Pueblo
    Posts
    6,907

    Default

    Check the condition of the brake hose lines. If the calipers are hanging by the brake lines, you may end up with trouble. I had an old brake line not let the pressure off the caliper on a old chevy truck. It got really hot and glazed the rotor. If the hoses are original, might be a good time to change them while you got everything apart.
    Per Ardua ad Astra

  10. #10
    Witness Protection Reject rondog's Avatar
    Join Date
    Jul 2007
    Location
    Parker, CO
    Posts
    8,285
    Blog Entries
    1

    Default

    I did 'em on my 2000 Silverado, don't ever want to do it again.....
    There's a lot more of us ugly mf'ers out here than there are of you pretty people!

    - Frank Zappa

    Scrotum Diem - bag the day!

    It's all shits and giggles until someone giggles and shits.....

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •