HEY! You leave my nutz outta this!Originally Posted by waxthis
Hey man, you right wing gun NUTZ have to eat don't ya.................
Colorado AR-15 Shooters Club Discussion Forums
Welcome to the Colorado AR-15 Shooters Club Discussion Forums.
Welcome to the Colorado AR-15 Shooters Club Discussion Forums.
HEY! You leave my nutz outta this!Hey man, you right wing gun NUTZ have to eat don't ya.................
My Feedback
"When law and morality contradict each other, the citizen has the cruel alternative of either losing his moral sense or losing his respect for the law." -Frederic Bastiat
"I am a conservative. Quite possibly I am on the losing side; often I think so. Yet, out of a curious perversity I had rather lose with Socrates, let us say, than win with Lenin."
― Russell Kirk, Author of The Conservative Mind
Take it back!Now we just need to get these indian taco clowns out of the reloading forum!
By the way, you NSA pricks, that Alex Jones link above is for you to feast your eyes.
My Feedback
"When law and morality contradict each other, the citizen has the cruel alternative of either losing his moral sense or losing his respect for the law." -Frederic Bastiat
"I am a conservative. Quite possibly I am on the losing side; often I think so. Yet, out of a curious perversity I had rather lose with Socrates, let us say, than win with Lenin."
― Russell Kirk, Author of The Conservative Mind
My rock chucker is what I no longer use. It had some of the runout issues requiring the twist and reseat method you described.Either has a tiny bit of play in the turret, in fact, I measured .008 front and .002 rear on a press in the FL RCBS sizing/decapping die I have in the Classic for a combined .006 deviation.
There's two ways to overcome that tiny bit of deviation if it bothers you. Put o-rings on the die between the turret and lockring - Lee dies already have this - and/or A little blue tape on the back edge of the turret head to even things out. The o-ring on the die seems to be a well known trick for any die set to allow the die to float a bit in the head and align itself to the shellplate. Others have reported (on any press) a half seat on the bullet, twist 180 and then full seat to reduce run-out.
If you're that twisted up about loading precision benchrest loads, the Lee turret press is not for you as you're likely to have an arsenal of concentricity gauges, precision benchrest dies, and other precision instruments and unlikely to have purchased a Lee turret press to begin with.
I auto-index with the Lee and it works fine. One of them did require a little tweaking of the nut on the rod to properly index. Instructions are included.
Someday I'll grow up and get a Dillon 550B for bulk and probably pick up a Rock Chucker for handloads. For now, the Lee presses fill both roles.
i should probably get dies that are more suited to the task.
Just doing what I can to stay on this side of the dirt.
Opps...My bad..
"An individual is only entiteld to one's rights as long as one respects the rights of others."...R.F.
Coughing up gremlins.......winning.
And for your Friday enjoyment:
My Feedback
"When law and morality contradict each other, the citizen has the cruel alternative of either losing his moral sense or losing his respect for the law." -Frederic Bastiat
"I am a conservative. Quite possibly I am on the losing side; often I think so. Yet, out of a curious perversity I had rather lose with Socrates, let us say, than win with Lenin."
― Russell Kirk, Author of The Conservative Mind
I would say it looks the same coming out....Butt.....I wont......
....
"An individual is only entiteld to one's rights as long as one respects the rights of others."...R.F.
I would say it looks the same coming out....Butt.....I wont...
My Feedback
"When law and morality contradict each other, the citizen has the cruel alternative of either losing his moral sense or losing his respect for the law." -Frederic Bastiat
"I am a conservative. Quite possibly I am on the losing side; often I think so. Yet, out of a curious perversity I had rather lose with Socrates, let us say, than win with Lenin."
― Russell Kirk, Author of The Conservative Mind
Sshhhhhh.....don't say anything. Embrace both moments!I would say it looks the same coming out....Butt.....I wont...
Posting Permissions
Reply With Quote
