Activity Stream

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums Articles Articles Blog Blogs Groups Groups

Today, 12:04

BigTTown replied to a thread RULES: Must Read, and acknowledge BEFORE posting in the Trading Post in Announcements

Trading post rules acknowledged.

1734 replies | 440077 view(s)

Yesterday, 22:17

BushMasterBoy replied to a thread Are you good with a Dremel? in Ask-A-Member: "I need help with..." plus DIY & Projects

Instead of polishing, can it be cerakote finished? I have no experience with cerakote. Some vendors listed below https://highcountryarmory.net/ ...

12 replies | 200 view(s)

Yesterday, 20:54

def90 replied to a thread Are you good with a Dremel? in Ask-A-Member: "I need help with..." plus DIY & Projects

Yeah, you are going to have to sand the entire thing in order to get a consistent finish. You bought that from a vendor? Is that normal or did you...

12 replies | 200 view(s)

Yesterday, 18:19

bellavite1 replied to a thread Are you good with a Dremel? in Ask-A-Member: "I need help with..." plus DIY & Projects

Thank you!

12 replies | 200 view(s)

Yesterday, 18:15

BushMasterBoy replied to a thread Are you good with a Dremel? in Ask-A-Member: "I need help with..." plus DIY & Projects

I asked AI on Google and it said this... "To smooth plastic, wet-sand with progressively finer grits of sandpaper (e.g., starting around 220 or...

12 replies | 200 view(s)

Yesterday, 12:41

bellavite1 replied to a thread Are you good with a Dremel? in Ask-A-Member: "I need help with..." plus DIY & Projects

You guys are a brave bunch....

12 replies | 200 view(s)

Yesterday, 12:08

whitewalrus replied to a thread Are you good with a Dremel? in Ask-A-Member: "I need help with..." plus DIY & Projects

I have smoothed some out with heat guns. Depending on plastic used, acetone may also work.

12 replies | 200 view(s)

Yesterday, 10:41

eddiememphis replied to a thread Are you good with a Dremel? in Ask-A-Member: "I need help with..." plus DIY & Projects

I have heard of a heat gun relaxing some of those ridges. Depends on what type of plastic they used to make it.

12 replies | 200 view(s)

Yesterday, 09:53

bellavite1 replied to a thread Are you good with a Dremel? in Ask-A-Member: "I need help with..." plus DIY & Projects

It is...hence the Dremel thing...

12 replies | 200 view(s)

Yesterday, 09:33

BushMasterBoy replied to a thread Are you good with a Dremel? in Ask-A-Member: "I need help with..." plus DIY & Projects

I was thinking cut some fine grade sandpaper in strips and put the gun in a vise. Make sure the gun is wrapped in a cloth. Use the strips of...

12 replies | 200 view(s)

Yesterday, 08:17

BPTactical replied to a thread Are you good with a Dremel? in Ask-A-Member: "I need help with..." plus DIY & Projects

Steal some of the Mrs emery boards she uses for her nails and get busy. You try a dremel and you will melt it. Slow & smooth Lou

12 replies | 200 view(s)

Yesterday, 07:56

eddiememphis replied to a thread Charlie Kirk shot in General Discussion

https://www.dailymail.co.uk/news/article-15096571/Trans-partner-Charlie-Kirk-killer-Tyler-Robinson.html...

53 replies | 1852 view(s)

Yesterday, 07:10

buffalobo replied to a thread Are you good with a Dremel? in Ask-A-Member: "I need help with..." plus DIY & Projects

^^^This, and it will be therapeutic for OCD. If you're unarmed, you are a victim

12 replies | 200 view(s)

Yesterday, 06:31

XJ replied to a thread Are you good with a Dremel? in Ask-A-Member: "I need help with..." plus DIY & Projects

Those look to be fixable with sandpaper.

12 replies | 200 view(s)

Colorado AR-15 Shooters Club Discussion Forums

Partners

Partners

About Us

Established - 2002